Sản phẩm tiêu biểu

Improving workability and productivity with a bi-shaft turret method. The cutting dust is collected by dust extractor. A substrate is clamped by a mechanical shaft. The movement (left, right, back and forth) of cutter carriage is very fast with using servomotor so that the recycle time can be shortened drastically. |
![]() |
![]() |
Type | 722-CAFMS/300 | 722-CAFMS/400 | 722-CAFMS/500 | FKC-T2 |
Roll diameter | φ300mm | φ400mm | φ500mm | φ300mm |
Roll width | 1600mm | |||
Core internal diameter | 3inch | |||
Cutting accuracy | ±0.1mm | |||
Tipped saw | φ355 x 3mm | φ455 x 3.2mm | φ610 x 3.6mm | φ355 x 3mm |
Tipped saw rotation speed | MAX 2000 rpm | |||
Substrate rotation speed | MAX 210 rpm | |||
Mechanical shaft for substrate | 1Mechanical shaft (air source required), Rotation drive. | 2Mechanical shaft (air source required), Rotation drive. | ||
Forward cutting speed | Three level automatic shift | |||
Touch panel | The cutting width and cutting number of pieces can be preset in three levels. Water spray device. Malfunctional warning. | |||
Dust extractor | Standard equipment (Cyclone filter type conpact dust) | |||
Option | Blade cooling device (air source required),Water spray device. | |||
The degree adjust system of tipped saw / speed and a rotation adjustment system. |
||||
Power | AC200V 3phases 50Hz/60Hz |
cutting materials : | film・paper・other hard materials |
![]() |
![]() |
The longitudinal and cross feeds for tape cutting are done automatically. The cutting dust is collected by dust extractor. |
![]() |
Type | 722-CAF/300 | 722-CAF/400 | 722-CAF/500 |
Roll diameter | φ300mm | φ400mm | φ500mm |
Roll width | 1600mm | ||
Core internal diameter | 3inch | ||
Cutting accuracy | ±0.1mm | ||
Tipped saw size | φ355 x 3mm | φ455 x 3.2mm | φ610 x 3.6mm |
Tipped saw rotation speed | MAX 2000 rpm | ||
Chuck rotation speed | MAX 210 rpm | ||
Forward cutting speed | Three level automatic shift | ||
Touch panel | The cutting width and cutting number of pieces can be preset in three levels. Malfunctional warning. | ||
Dust extractor | Standard equipment | ||
Option | Blade cooling device (air source required), Water spray device. | ||
Power | AC200V 3phases 50Hz/60Hz |
cutting materials : | film・paper・other hard materials |
![]() ![]() |
FC-2300(Substrate:MAXφ300mm、L=1600mm) The cutting blade is equipped with two pieces (saw and V blade). Therefore, it prevents heating adhesion to make good looking cutting edge. The cutting dust is collected by dust extractor. A substrate is clamped by a mechanical shaft. The movement (left, right, back and forth) of cutter carriage is very fast with using servomotor so that the recycle time can be shortened drastically. As a option, there is substrate carry-in device. |
![]() |
![]() |
FC-203BV(Substrate:MAXφ300mm、L=1600mm) Special V-blade (twin blades) and special bite blade are used. With high-precision sharp knife it can cut without rewinding film and welding. |
![]() |
![]() |
![]() |
Vui lòng liên hệ : 081.2887551 - 0918121454 - (Ms. Ngọc).
Danh mục sản phẩm
Gia Công Cơ Khí Chính Xác
Bàn Nâng Thủy Lực
Máy Đóng Gói
Dụng Cụ ECLIPSE
Máy cắt Kindai
Máy Giặt Công Nghiệp
Máy Ép Phế Liệu
Máy Móc Dệt May
Tủ So Màu
Máy Dò Kim Loại
Máy Giặt Miele
Thiết Bị Đo
Máy Dán Thùng Carton
Máy Dán Nhãn
Máy Tách Nhãn
Máy Đóng Nắp Chai
Máy Cắt Băng Keo
Băng Chuyền - Băng Tải
Máy Đóng Đai
Máy Chiết Rót
Bình Chữa Cháy
Máy Khuấy Trộn
Bồn Inox - Tank
Máy Tuốt Vỏ Dây Điện
REX - ASADA
Máy Dán Màng Co Tự Động
Máy May Bao Fischbein
Nước Tinh khiết
Cảm Biến Autonics
Cảm Biến Sensys
Công Tắc Phao RIKO
Hỗ trợ trực tuyến
LIÊN KẾT WEB
Liên kết website:
VIDEO CLIP
Đối tác